- #TOOL AS CROSSHAIR IN MASTERCAM X4 MANUAL#
- #TOOL AS CROSSHAIR IN MASTERCAM X4 VERIFICATION#
- #TOOL AS CROSSHAIR IN MASTERCAM X4 SOFTWARE#
- #TOOL AS CROSSHAIR IN MASTERCAM X4 WINDOWS#
Repeat the steps to select the other perpendicular line below the first line that we created. Select which line to keep Select the line above the existing one. Create/Line/ Create Line Perpendicular and set parameters to: Select line, arc or spline Select the existing line Sketch a point Select the Endpoint of the existing line opposite the origin. GEOMETRY CREATION STEP 1: CREATE THE 2D GEOMETRY IN THE RIGHT SIDE VIEW Option 1The geometry file, Tutorial4_geometry.zip, can be downloaded from The finish part, Tutorial4_finish.zip including the toolpaths, is also provided on the same location Option 2-Create the geometry using the following instructions: Create the 2D profile in the Right side view: Create/Arc/ Create Circle Center Point and set parameters to: Diameter = 5.0 Center Origin Create/Line/ Create Line Endpoint and set parameters to: Specify an endpoint = Origin Line length = 2.45 Angle = 165 deg. Running the Verify function to machine the part on the screen.
#TOOL AS CROSSHAIR IN MASTERCAM X4 VERIFICATION#
The Student will check the toolpath using Mastercam’s Verify verification module by: Defining a 3-dimensional block, the size of the workpiece. Machine the second groove using Transform-Rotate toolpath. Removing the material inside of one groove using contour toolpath. Facing the other two flat surfaces using Transform-Rotate toolpath. Create an operation for each face using the same work offset (G54). The Student will create a 2-dimensional milling toolpath in different Tplanes consisting of: Using View Manager to select the Tplane for each face. Changing the view of the part for better visualisation. Creating circles knowing the diameter and the center location. Creating the 3D geometry using translate command. The Student will design a 3-dimensional drawing by: Creating the 2D geometry in the Right Side view. 7-1 Swarf 5-Axis With Wall Defined By Using 2 Contours Tutorial. 6-1 Drill 5-Axis and Circle Mill 5-Axis Tutorial. 4-1 Rotary4-Axis Toolpath and Axial 4ax Tutorial. 2-1 Axis Substitution, Rolldie C-Hook Tutorial. 1-1 Axis Substitution To Create A Cylindrical and A Conical Helix Tutorial. A-1 Axis Substitution, Rotary Axis Positioning and Transform-Rotate Tutorial.
#TOOL AS CROSSHAIR IN MASTERCAM X4 WINDOWS#
Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation Mastercam Verify is created in conjunction with Sirius Systems Corporation Windows 95, and Windows NT Windows XP are registered trademarks of Microsoft Corporation. Trademarks Mastercam is a registered trademark of CNC Software, Inc. This document may not, in whole or part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent, in writing, from InHouse Solutions Inc.
#TOOL AS CROSSHAIR IN MASTERCAM X4 MANUAL#
Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you.Ĭopyrights This manual is protected under the copyright laws of Canada and the United States. has been advised of the possibility of such damages. be liable for direct, indirect, or consequential damages resulting from any defect in the manual, even if In-House Solutions Inc. Should the manual prove defective following its purchase, the buyer (and not In-House Solutions Inc., its distributor, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. manual is sold or licensed "as is." The entire risk as to its quality and performance is with the buyer.
#TOOL AS CROSSHAIR IN MASTERCAM X4 SOFTWARE#
makes no warranties, either express or implied, with respect to this manual or with respect to the software described in this manual, its quality, performance, merchantability, or fitness for any particular purpose. reserves the right to make improvements to this manual at any time and without notice.ĭisclaimer Of All Warranties And Liability In-House Solutions Inc. Software: Mastercam X Mill Authors: Mariana Lendel ISBN: 978-1-92 Mastercam X Training Tutorials – 4 & 5 Axis Mill Applications Revised Date: JCopyright © 1984 - 2009 In-House Solutions Inc. To order more books: Call 1-80 or Visit or Contact your Mastercam Dealer
0 kommentar(er)
